Grip glossary
Plain definitions for the words grip makers use.
A
- A2 grip
- The standard AR-15 pistol grip: narrow, raked back, with a finger nub on the front. Most aftermarket grips exist to replace it.
- Adhesive wrap
- A thin, die-cut sheet that sticks to a pistol frame to add texture. Also called grip tape. See pistol grip tape.
- Angled foregrip
- A support-hand grip that slopes forward instead of hanging straight down. See foregrips.
- Any other weapon (AOW)
- A category of firearm under the U.S. National Firearms Act. The ATF considers a pistol with a vertical fore grip to be one. See foregrip laws.
B
- Backstrap
- The rear face of a pistol grip, where the web of the hand sits. Many pistols have interchangeable backstraps to change size.
- Bar end plug
- A cap pressed into the open end of a handlebar. It protects the rider in a crash and holds bar tape in place.
- Bar tape
- The wrap on drop handlebars. See road bar tape.
- Beavertail
- An upswept extension at the top rear of a grip that protects the web of the hand and lets it sit high.
- Bevel
- One of the eight flat faces on a racquet handle. Firm, thin grips make bevels easier to feel.
- Bird’s-head grip
- A short, curved grip on stockless shotgun-type firearms that lets recoil roll the gun in the hand.
- Bobtail
- A 1911 frame with the rear corner of the grip rounded off. It needs grip panels cut to match.
- Boot grip
- A short revolver grip that ends at the bottom of the frame, for concealment.
- Build-up tape
- Extra layers of tape under a golf grip to increase its diameter. One wrap adds about 1/64 inch.
- Bushing (1911)
- A threaded sleeve in the frame that a grip screw fastens into. Thin grips need slim bushings.
C
- Checkering
- A texture of small pointed diamonds formed by crossing rows of grooves. See the texture library.
- Cobblestone
- Hogue’s name for the pebbled texture on its rubber grips.
- Compound
- The specific rubber or polymer formula of a grip. Softer compounds grip better and wear faster.
- Cord
- Cotton fiber molded into a rubber golf grip for wet-weather traction. See cord.
- Core size
- The inside diameter of a golf grip, commonly 0.580 or 0.600 inch, matched to the shaft.
D
- Dual compound
- A grip molded from two rubbers of different hardness, usually firm at the ends and soft in the middle.
- Durometer
- A measure of hardness for rubber and plastics. On the Shore A scale used for grips, lower numbers are softer.
E
- EVA
- Ethylene-vinyl acetate, a closed-cell foam used for light, cushioned grips. See EVA foam.
- Extensor
- A muscle that opens the hand. Training extensors balances gripper work.
F
- Figure 8 strap
- A lifting strap of two joined loops that locks the hand to the bar. For deadlifts and shrugs only.
- Finger grooves
- Scallops on the front of a grip that locate each finger.
- Fire control unit
- The serialized internal chassis of pistols such as the SIG P320 and P365. The grip module around it is an ordinary accessory.
- Flange
- A raised lip at the inner end of a handlebar grip.
- Front strap
- The front face of a pistol grip, under the fingers.
G
- G10
- A laminate of fiberglass cloth and epoxy, machined into grip panels. See G10.
- Granulate
- A mineral grit texture like sandpaper. See the texture library.
- Grip angle
- The tilt of a grip relative to the bore. See grip angle explained.
- Grip module
- The replaceable polymer grip of a modular pistol.
- Grip safety
- A lever on the backstrap that must be pressed by the hand before the pistol can fire. Accessories must not block it.
H
- Half waffle
- A motocross grip pattern with raised squares on the underside only.
- Handstop
- A small projection on a rifle handguard that gives the support hand an index point.
K
- Knurling
- A fine diamond pattern rolled or cut into metal, as on a barbell.
L
- Lasso strap
- The common lifting strap: a strap with a loop at one end that tightens around the wrist.
- Lock-on grip
- A handlebar grip with a clamp that bolts it to the bar so it cannot rotate.
M
- M-LOK
- A slot-based system for attaching accessories to rifle handguards.
- Magazine well (magwell)
- The opening the magazine enters. A flared magwell needs grip panels relieved at the bottom.
- Micarta
- A laminate of fabric or paper in phenolic resin. See Micarta.
- Monogrip
- Hogue’s one-piece rubber revolver grip.
O
- Overgrip
- A thin wrap applied over a racquet’s base grip and replaced often.
- Overmold
- A layer of rubber molded over a rigid core.
P
- Palm swell
- A bulge in the side of a grip that fills the hollow of the palm.
- Palmswell insert
- Smith & Wesson’s term for the interchangeable grip inserts on M&P pistols.
- Peg frame
- Ruger’s revolver grip mounting, where the grip slides over a short stud instead of a full frame.
- Picatinny rail
- A standardized slotted rail for mounting accessories on firearms.
- Pinky extension
- A magazine floor plate with a rest for the little finger. See magazine grip extensions.
- Pistol grip
- On a rifle or shotgun, the separate handle for the firing hand.
- Plus4
- Golf Pride’s name for a grip with a larger lower hand, equal to four extra wraps of tape.
- Polyurethane (PU)
- The soft, tacky polymer used for overgrips, golf wraps and bar tape. See polyurethane.
R
- Reduced taper
- A golf grip that narrows less toward the lower hand than a traditional grip.
- Replacement grip
- The thick, cushioned base grip on a racquet handle.
- Round butt
- A revolver grip frame with a curved rear corner. See frame sizes.
S
- Scales
- Another word for grip panels, especially on knives and older handguns.
- Self-fusing tape
- Silicone tape that bonds to itself without adhesive.
- Slip-on sleeve
- A rubber tube stretched over a pistol grip. See grip sleeves.
- Square butt
- A revolver grip frame with a defined rear corner.
- Stippling
- A texture of small divots melted into polymer. See stippling explained.
T
- Tack
- The sticky feel of a surface, independent of its texture.
- Thermoplastic elastomer (TPE)
- A rubber-like plastic that can be injection molded. Common in overmolded grips.
- Throttle tube
- The plastic sleeve on a motorcycle’s right handlebar that the throttle grip fits over.
- Traction
- How strongly a grip resists the hand sliding. On this site we rate it from 1, smooth, to 5, very aggressive, based on the texture type and the maker’s own description. See how we evaluate.
V
- Vertical foregrip
- A support-hand grip that hangs straight down from a rifle’s handguard.
W
- Wraparound grip
- A one-piece grip that covers the front strap as well as the sides.