Best AR-15 pistol grips
Grip angle and width decide comfort on an AR. Texture and storage are tie-breakers.
The standard A2 grip is narrow, steeply raked and has a finger nub that suits few hands. It dates from an era of long fixed stocks. With a collapsed carbine stock and a squared-up stance, a more vertical grip puts less bend in the wrist, which is why most modern grips reduce the angle.
Every grip here attaches with one screw and fits standard AR-15 and AR-10 pattern lowers. Swapping one is a ten-minute job: see how to change an AR-15 pistol grip.
Quick picks
| Pick | Grip | Why |
|---|---|---|
| Top pick | BCM Gunfighter Grip Mod 3 | Reduced angle, wider body and a built-in tang that closes the trigger guard gap. |
| Budget pick | Magpul MOE Grip | An inexpensive step up from the A2 with storage. |
| Smaller hands | BCM Gunfighter Grip Mod 0 | Slim like an A2 with the same reduced angle. |
| Rubber feel | Magpul MOE-K2+ Grip | Vertical angle with a rubber overmold. |
| Adjustable fit | Magpul MIAD Gen 1.1 Grip Kit | Interchangeable front and back straps. |
How to choose
Start with angle
A more vertical grip suits short lengths of pull and squared stances. A traditional raked angle can still feel better on a rifle shot prone or from a bench with a long stock. If you run a carbine stock one or two clicks out, go vertical. More in grip angle explained.
Then width
Slim grips similar to the A2 suit small and medium hands and gloved use. Wider grips fill large hands and spread recoil over more palm. BCM states its Mod 2 and Mod 3 are up to a quarter inch wider than its Mod 0 and Mod 1.
Backstrap height
A raised backstrap, sometimes called a beavertail, fills the gap under the receiver’s rear lug so the web of your hand sits high and consistent.
Texture and overmold
Hard polymer with molded texture is durable and slides easily out of a bag. Rubber overmold is tackier in wet or cold weather and collects more lint.
The grips
Gunfighter Grip Mod 3
Best for most carbines and most hand sizes
- Type
- AR-15 pistol grip
- Material
- Impact-resistant polymer
- Texture
- Molded texture
- Traction
- Medium
- Adds
- Wider body, high backstrap
- Install
- One grip screw
- Price tier
- Budget
The Mod 3 has BCM’s reduced grip angle, a high-rise backstrap and a body up to a quarter inch wider than the Mod 0 and Mod 1. Its forward extension is molded in, closing the gap behind the trigger guard. A hinged trap door with a rubber gasket covers a storage compartment. Made in the USA.
Trade-off. The fixed tang may not sit flush against some billet lowers with unusual trigger guards. BCM points those builds to its other models, which use removable inserts.
Gunfighter Grip Mod 0
Best for small hands and gloved use
- Type
- AR-15 pistol grip
- Material
- Impact-resistant polymer
- Texture
- Molded texture
- Traction
- Medium
- Adds
- Slim body, low backstrap
- Install
- One grip screw
- Price tier
- Budget
The Mod 0 keeps a slim profile close to the A1 and A2 grips while using the reduced angle. It ships with two inserts that fill the space behind the trigger guard. The Mod 1 is the same size with a high-rise backstrap, and the Mod 2 adds interchangeable backstraps on the wider body.
Trade-off. Large hands may find it thin.
MOE Grip
Best for a low-cost first upgrade
- Type
- AR-15 pistol grip
- Material
- Reinforced polymer
- Texture
- Molded texture
- Traction
- Medium
- Adds
- Fuller body with a backstrap
- Install
- One grip screw
- Price tier
- Budget
The MOE is a one-piece polymer grip with a hand-filling shape, a backstrap and a capped storage core. It keeps a traditional angle, so it feels familiar to anyone coming from an A2 while fixing the A2’s narrow body and finger nub.
Trade-off. The traditional angle is less comfortable with a short stock than Magpul’s K2 or BCM’s grips.
MOE+ Grip
Best for cold or wet weather on a traditional angle
- Type
- AR-15 pistol grip
- Material
- Polymer with rubber overmold
- Texture
- Rubberized
- Traction
- Medium
- Adds
- Fuller body with a backstrap
- Install
- One grip screw
- Price tier
- Budget
The same shape as the MOE with a wrap-around rubber overmold for a tackier hold.
Trade-off. Rubber shows wear and picks up debris sooner than bare polymer.
MOE-K2+ Grip
Best for a vertical angle with a soft surface
- Type
- AR-15 pistol grip
- Material
- Polymer with rubber overmold
- Texture
- Rubberized
- Traction
- Medium
- Adds
- Full-size body, vertical angle
- Install
- One grip screw
- Price tier
- Budget
Magpul describes the K2 as a more vertical grip angle in a full-size design, and the K2+ as that grip with rubber overmolding. A hard polymer lower edge keeps the rubber from catching. The plain MOE-K2 is the same shape in textured polymer, and a larger K2-XL has joined the line.
Trade-off. No interchangeable straps. If the size is wrong, you change grips.
MOE-K and MOE SL Grips
Best for short, light builds
- Type
- AR-15 pistol grip
- Material
- Reinforced polymer
- Texture
- Molded texture
- Traction
- Medium
- Adds
- Compact and slim
- Install
- One grip screw
- Price tier
- Budget
The MOE-K is Magpul’s compact grip for PDW-style firearms, with a steep vertical angle and minimal bulk. The MOE SL is a slim grip with a more vertical angle and a backstrap.
Trade-off. Neither has the storage core of the full-size grips, and both can feel small in large hands.
MIAD Gen 1.1 Grip Kit
Best for dialing in fit, or one rifle shared by several shooters
- Type
- Modular AR-15 pistol grip
- Material
- Reinforced polymer
- Texture
- Molded texture
- Traction
- Medium
- Adds
- Varies with the straps fitted
- Install
- One grip screw
- Price tier
- Mid-range
MIAD stands for Mission Adaptable. The kit includes interchangeable front straps and backstraps so you can change the grip’s size and the presence of a finger groove without buying another grip. It accepts Magpul’s storage cores.
Trade-off. Costs more than fixed grips, and the seams between parts are noticeable to some hands.
Type 23 P-Grip
Best for an aggressive texture on a reduced angle
- Type
- AR-15 pistol grip
- Material
- Polymer
- Texture
- Molded texture
- Traction
- Aggressive
- Adds
- Slim to medium body
- Install
- One grip screw
- Price tier
- Budget
B5’s grip pairs a reduced angle with a fairly sharp molded texture and a high backstrap. It has no storage compartment, which keeps it light and simple, and it comes in the usual range of furniture colors.
Trade-off. The texture is rougher than BCM or Magpul polymer, which not everyone wants bare-handed.
Ergo Grip, SureGrip overmold
Best for a contoured, cushioned hold
- Type
- AR-15 pistol grip
- Material
- Polymer core with rubber overmold
- Texture
- Rubberized
- Traction
- Medium
- Adds
- Palm-filling body
- Install
- One grip screw
- Price tier
- Budget
The Ergo Grip has a rigid core under a textured rubber skin, with a swell that fills the palm and a raised backstrap. It is one of the longest-running alternatives to the A2 and is offered in right-hand and ambidextrous shapes.
Trade-off. A traditional angle, and the pronounced contours either suit your hand or they do not.
OverMolded AR-15 Grip
Best for shooters who like finger grooves
- Type
- AR-15 pistol grip
- Material
- Rubber over a rigid insert
- Texture
- Cobblestone
- Traction
- Mild
- Adds
- Finger grooves, soft body
- Install
- One grip screw
- Price tier
- Budget
Hogue’s rubber AR grip uses the same Cobblestone texture and finger grooves as its handgun grips, molded over a stiff insert. It is offered with and without a beavertail.
Trade-off. Finger grooves fix your hand position, and soft rubber is the least durable surface here.
Questions people ask
Do AR-15 grips fit AR-10 rifles?
Standard AR-15 pistol grips fit AR-10 and SR-25 pattern lowers, because the grip mounting lug is the same. Check any grip with a forward tang against an oversized trigger guard.
What tool do I need to change an AR-15 grip?
Usually a long hex key or a flat screwdriver, depending on the screw supplied. Take care not to lose the safety selector spring and detent that the grip holds in place. See the step-by-step guide.
Is a vertical grip angle better?
It is more comfortable for most people with a short length of pull, because the wrist stays straighter. With a long fixed stock or when shooting prone, a traditional angle can feel more natural.